PIC18F83J11T-I/PT【PDF 62/332 页】IC PIC MCU FLASH 4KX16 80TQFP

收藏本站

您好，
买卖IC网欢迎您。
请登录
免费注册

买卖IC网

Sheet目录3871

58页 59页 60页 61页 [62页]63页 64页 65页 66页

PIC18F85J11 FAMILY

DS39774D-page 154

2010 Microchip Technology Inc.

12.1

Timer0 Operation

Timer0 can operate as either a timer or a counter. The

mode is selected with the T0CS bit (T0CON<5>). In

Timer mode (T0CS = 0), the module increments on

every clock by default unless a different prescaler value

is selected (see Section 12.3 “Prescaler”). If the

TMR0 register is written to, the increment is inhibited

for the following two instruction cycles. The user can

work around this by writing an adjusted value to the

TMR0 register.

The Counter mode is selected by setting the T0CS bit

(= 1). In this mode, Timer0 increments either on every

rising or falling edge of pin RA4/T0CKI. The increment-

ing edge is determined by the Timer0 Source Edge

Select bit, T0SE (T0CON<4>). Clearing this bit selects

the rising edge. Restrictions on the external clock input

are discussed below.

An external clock source can be used to drive Timer0;

however, it must meet certain requirements to ensure

that the external clock can be synchronized with the

internal phase clock (TOSC). There is a delay between

synchronization and the onset of incrementing the

timer/counter.

12.2

Timer0 Reads and Writes in

16-Bit Mode

TMR0H is not the actual high byte of Timer0 in 16-bit

mode. It is actually a buffered version of the real high

byte of Timer0 which is not directly readable nor writ-

able (refer to Figure 12-2). TMR0H is updated with the

contents of the high byte of Timer0 during a read of

TMR0L. This provides the ability to read all 16 bits of

Timer0 without having to verify that the read of the high

and low byte were valid, due to a rollover between

successive reads of the high and low byte.

Similarly, a write to the high byte of Timer0 must also

take place through the TMR0H Buffer register. The high

byte is updated with the contents of TMR0H when a

write occurs to TMR0L. This allows all 16 bits of Timer0

to be updated at once.

FIGURE 12-1:

TIMER0 BLOCK DIAGRAM (8-BIT MODE)

FIGURE 12-2:

TIMER0 BLOCK DIAGRAM (16-BIT MODE)

Note: Upon Reset, Timer0 is enabled in 8-bit mode with clock input from T0CKI max. prescale.

T0CKI Pin

T0SE

T0CS

FOSC/4

Sync with

Internal

Clocks

TMR0L

(2 TCY Delay)

Internal Data Bus

PSA

T0PS<2:0>

Set

TMR0IF

on Overflow

Programmable

Prescaler

Note: Upon Reset, Timer0 is enabled in 8-bit mode with clock input from T0CKI max. prescale.

T0CKI Pin

T0SE

T0CS

FOSC/4

Sync with

Internal

Clocks

TMR0L

(2 TCY Delay)

Internal Data Bus

PSA

T0PS<2:0>

Set

TMR0IF

on Overflow

TMR0

TMR0H

High Byte

Read TMR0L

Write TMR0L

Programmable

Prescaler

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

采购需求

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

我的联系方式